NS0-527 Exam Info and Free Practice Test All-in-One Exam Guide Aug-2023
Pass Network Appliance NS0-527 Actual Free Exam Q&As Updated Dump Aug 27, 2023
NEW QUESTION # 66
Your customer wants to implement a solution to protect only a select number of NFSv3 volumes in aparticular aggregate that stores their mission-critical application data. The customer wants the volume's data replicated to secondary storage and have application write operations fail if they cannot be replicated. The customer needs to maintain a zero RPO and a very low RTO.
In this scenario, which solution satisfies these requirements?
- A. SnapMirror Synchronous using Sync mode
- B. SnapMirror Synchronous using StrictSync mode
- C. Mirrored SVMs using MetroCluster
- D. Mirrored aggregates using SyncMirror
Answer: D
NEW QUESTION # 67
Network bandwidth between your the primary and secondary sites is limited. You believe that data compression combined with volume SnapMirror would help solve this problem.
In this scenario, which statement is correct?
- A. A SnapMirror source cannot becompressed but the destination volume can be.
- B. Data compression can be enabled on the source storage system and will remain intact through SnapMirror.
- C. Compression can be enabled independently between the source and the destination.
- D. Data compression and SnapMirror are incompatible.
Answer: B
NEW QUESTION # 68
Click the Exhibit button.
cluster2::>snapmirror show -instance
Source Path: svm1:svm1_vol3
Destination Path: svm1_2:svm1_2_vol2
Relationship Type: DP
Relationship Group Type: none
SnapMirror Schedule: 5min
SnapMirror Policy Type: async-mirror
SnapMirror Policy: DPDefault
Tries Limit: -
Throttle (KB/sec): unlimited
Mirror State: Snapmirrored
Relationship Status: Idle
Last Transfer Type: update
Last Transfer Error: -
Last Transfer Size: 72 KB
Last Transfer Network Compression Ratio: 1:1
Last Transfer Duration: 0:0:2
Last Transfer From: svm1:svm1_vol3
Last Transfer End Timestamp: 09/24 13:10:04
Progress Last Updated: -
Relationship Capability: 8.2 and above
Lag Time: 0:0:55
Number of Successful Updates: 1
Number of Failed Updates: 0
Number of Successful Resyncs: 0
Number of Failed Resyncs: 0
Number of Successful Breaks: 0
Number of Failed Breaks: 0
Total Transfer Bytes: 212992
Total Transfer Time in Seconds: 5
You want to view your SnapMirros relationship to make sure it is up to date. You issue the snapmirror show -instance command. Referring to the exhibit, how long has it been since the last SnapMirror update has successfullyoccurred?
- A. 5 minutes
- B. 55 minutes
- C. 5 seconds
- D. 55 seconds
Answer: D
NEW QUESTION # 69
You are performing a routine health check for a customer and need to determine if the disk shelf firmware is up to date.
From My AutoSupport, which report would you use?
- A. Upgrade Advisor
- B. Visualization
- C. Event Viewer
- D. Transition Advisor
Answer: B
NEW QUESTION # 70
On a Windows host, you want to make a consistent database backup of a physical SQL server where the database is on iSCSI-connected LUNs on aclustered Data ONTAP system.
In addition to SnapDrive for Windows, which three NetApp software products should be installed to satisfy this requirement? (Choose three.)
- A. Microsoft iSCSI Software Initiator
- B. Snap Manager for SQL
- C. On Command Unified Manager
- D. On Command Workflow Automation
- E. iSCSI Host Utilities
Answer: A,B,E
NEW QUESTION # 71
Your customer wants to be notified of SnapMirror lag errorswithin 15 minutes. The customer is not interested in maintaining custom scripts.
How would you accomplish this task?
- A. Use OnCommand Unified Manager to generateVolume Transfer Status reports on a schedule.
- B. Use OnCommand Unified Manager to create an error alert for SnapMirror Relationship lag.
- C. Use OnCommand System Manager to create a warning alert for SnapMirror lag.
- D. Use OnCommand System Manager to notify on Protection Health errors.
Answer: B
NEW QUESTION # 72
You want to provide your team with a SnapProtect report that shows how many backups succeeded, were delayed, and failed over the last 30 days. You also want detailed information about the jobs, agents, and clients.
WhichCommCell report provides the necessary information?
- A. Health
- B. SLA
- C. Backup Job Summary
- D. Activity
Answer: C
NEW QUESTION # 73
A customer needs to report on the SnapMirror and SnapVault relationships in their cluster.
Which two tools provide this information? (Choose two.)
- A. Config Advisor
- B. OnCommand Unified Manager
- C. OnCommand Insight
- D. OnCommand System Manager
Answer: B,D
NEW QUESTION # 74
You decide to enable SnapMirror network compression on your NetApp clustered Data ONTAP environment.
Which two statementsare correct about enabling this feature? (Choose two.)
- A. You may only enable SnapMirror network compression on one HApair in a cluster, and traffic 1-1 is limited to routing through those nodes.
- B. The data is compressed only while it traverses the network.
- C. The data transfer between the clusters must use the NDMP protocol.
- D. The compression engine creates multiple transfer threads corresponding to the number of CPUs on the source storage system.
Answer: B,D
NEW QUESTION # 75
In clustered Data ONTAP, you are creating MirrorAndVault XDP relationships between existing primary and secondary volumes. The Snapshot copy policies have already been created and assigned. The peering is already established and functional.
In clustered Data ONTAP, which three actions should be taken? (Choose three.)
- A. Create and initialize the SnapMirrorrelationship.
- B. Create the transfer policy.
- C. Add the inter-cluster LIF to the broadcast domain.
- D. Create the intercluster LIFs.
- E. Set up the retention on the secondary volume.
Answer: A,B,E
NEW QUESTION # 76
What are two ways to determine if yourSnapMirror relationships are up-to-date? (Choose two.)
- A. Use ONTAP System Manager and navigate to Protection -> Volume Relationships on the source cluster.
- B. Use Active IQ Unified Manager and navigate to Protection -> Volume Relationships.
- C. Use ONTAP System Manager and navigate to Protection -> Volume Relationships on the destination cluster.
- D. Use Active IQ and navigate to Cluster -> Volumes -> Protection.
Answer: C,D
NEW QUESTION # 77
A customer wants to create a new SnapMirror relationship to provide only disaster recovery for their organization.
Which relationship type and policy type should they specify in this scenario?
- A. XDP and MirrorAllSnapshots
- B. XDPand XDPDefault
- C. DP and MirrorAndVault
- D. DP and XDPDefault
Answer: A
NEW QUESTION # 78
A customer wants tochange a SnapMirror replication schedule to update more frequently.
They have 25 GB of data per update to be replicated along a single 1 Gbps Ethernet link.
In this scenario, what is the minimum amount of time required between SnapMirror updates?
- A. 5 minutes
- B. 3 minutes
- C. 20 minutes
- D. 200 minutes
Answer: C
NEW QUESTION # 79
You have a NAS volume containing 100 GB of data and daily change rate of 10%. You want to keep seven daily Snapshot copies. What is the minimum size for the volume?
- A. 170 GB
- B. 110 GB
- C. 220 GB
- D. 100 GB
Answer: A
NEW QUESTION # 80
You have multiple load-sharing destinations for a volume in a storage virtual machine. The source volume has become unavailable and you want to make one of the destination volumes the new source.
What happens to the original source volume?
- A. The original source volume goes offline.
- B. The promoteoperation takes the original source volume offline.
- C. The initialize operation deletes the original source volume.
- D. The promote operation deletes the original source volume.
Answer: D
NEW QUESTION # 81
You are performing a routine health check for a customer and need to determine if the disk shelf firmware is up to date. From My AutoSupport, which report would you use?
- A. Upgrade Advisor
- B. Visualization
- C. Event Viewer
- D. Transition Advisor
Answer: B
NEW QUESTION # 82
Click the Exhibit button.
Your customer wants to protect a volume and replicate it to a secondary volume. The customer has tried to configure this relationship using OnCommand System Manager. Upon reviewing this newly configured relationship, you discover that the configuration does not satisfy the customer's stated requirements.
Referring to the exhibit, what should you do to ensure that the volume is protected?
- A. Deletethe relationship and recreate it.
- B. Initialize the relationship.
- C. Change the schedule to hourly.
- D. Resynchronize the relationship.
Answer: A
NEW QUESTION # 83
......
Online Questions - Valid Practice NS0-527 Exam Dumps Test Questions: https://lead2pass.examdumpsvce.com/NS0-527-valid-exam-dumps.html
